Batam Medical Shop

Midmark M9 Autoclave Ultraclave Ritter Sterilizer

M9 is so efficient that it can pass the air removal tests required on systems vacuum steam autoclave more complex, ensuring good steam penetration for those loads difficult.

More details

On sale On sale!
$1,700.00 tax incl.

Loyalty program By buying this product you can collect up to 170 reward points as a voucher of $170.00. Your reward points.



M9 UltraClave Features:

    
Removal technology air pulses
    
Steam-Flush Pressure-Pulse Air Removal System of the M9 is so efficient that it can pass the air removal tests required on systems vacuum steam autoclave more complex, ensuring good steam penetration for those loads difficult. In addition, less complexity means better reliability and an economical solution for your sterilization needs.

    
Convenience at a glance
    
The LCD display indicates cycle selected, cycle temperature and exposure time. When the cycle enters sterilization mode, temperature, pressure, and the remaining cycle time shown. Remaining cycle time is also shown in the dry mode. Note: The temperature and pressure are not displayed in the dry mode.

    
No instruments wetter
    
Once sterilization is complete, the autoclave door automatically opens and silently to dispel water vapor and drying the instruments. You'll have dry, sterile instruments every time.

    
Security Features
    
If the door is not completely closed or the reservoir water level is low, the LCD provides the appropriate message. In any case, sterilization will not continue until you have attended the unit.

    
Easy Drain and Fill
    
For ease of emptying and filling the tank fill port M9 and the drain are at the front of the unit, at the top or at the rear.

    
Optional Printer Accessory
    
The M9 printer accessory provides a permanent record of the cycles, temperatures and pressures during a cycle.

    
Auto Program Controls
    
Programmable controls allow the creation of different sterilization cycle parameters for special needs. Programmable buttons allow you to change the following: Exposure time (3-90 minutes), temperature (230-275 ° F), Dry Time (0 to 60 minutes), or Vent (slow or fast). The buttons # 1 and # 2 allow you to store the change if desired.

    
Pre-Programmed Controls
    
Four sterilization cycle controls preprogrammed: Unwrapped (132 ° C or 270 ° C for 3 minutes), bags (132 ° C or 270 ° C for 5 minutes), Packs (121 ° C or 250 ° F for 30 minutes ) Handpieces (unwrapped and pouched) (132 º C or 270 º C for 6 minutes).

    
LCD Display
    
Indicates cycle selected, temperature and exposure time. During the cycle, the display shows messages describing the state of the cycle. When the cycle enters the sterilizing mode, the remaining time is displayed as well as temperature and pressure.

Specifications:

    
Overall length w / plug: 20.13 "(51 cm)
    
Width: 15.3 "(38.9 cm)
    
W total height / printer: 15.8 "(40.1 cm)
    
Countertop Area: 15.3 "x 20.38" (38.9 cm x 51.8 cm)
    
Camera: 9 "diameter (22.9 cm) 15" deep (38.0 cm) 3.5 gal. useful volume (13.4 liters)
    
Trays: Two large - 7 5/16 "W x 12" L x 7/8 "D (18.6 cm x 30.5 cm x 2.2 cm) Two small - 5 5/8" W x 12 "L x 7/8" D (14.3 cm x 30.5 cm x 2.2 cm)
    
Unit Weight: 73 lbs. (33.1 kg)
    
Shipping Weight: 81 lbs. (36.7 kg)
    
Water tank capacity: 1.1 gal. (4.1 liters)
    
Electrical Requirements: 115 VAC, 50/60 Hz, single phase 15 amp, 115 VAC has 1425 watt tubular immersion heater, UL61010A-1, UL61010-2-041, CAN / CSA C22.2 No. 1010, CAN / CSA C22 0.2 No. 1010.2-041-96

A separate circuit (dedicated) is recommended for this sterilizer.
Meets the requirements of ASME Code boilers and pressure vessels.
 


The M9 autoclave could not be easier and is time tested for reliability. You only have to load it ... set ... and forget it. Select the cycle and the time is set for you. Press "Start" and the M9 fills with the correct amount of water. Once the sterilization process is complete, the door opens automatically and quietly to dissipate the steam, giving you fast drying time for your instruments. Features include:

    
Exclusive automatic door opening for ease of use and fast drying time

    
Steam-Flush Pulse Pressure air extraction system ensures adequate penetration of steam

    
Self Program Controls enable you to create different cycle parameters to meet specific instrument processing

    
Preset controls for convenience

    
LCD screen for easy viewing of the indicators

Cart  

(empty)

New products

No new product at this time

Batam Medical Shop is an Upfront Merchant on TheFind. Click for info.